10 Best Laser Level Reviews
A top notch laser level could very well mean the difference between good construction work and a sloppy end product. The most accurate laser level would then obviously be the best choice if you want dead center construction accuracy. Depending on what your building needs are you might want to invest in either a small laser level or a more industrious outdoor laser level.
Here is our Review of the Top 10 Best laser Levels for 2017:
- 1. DEWALT DW088K Self-Leveling Cross Line Laser
- 2. Johnson Level Tool 99 006K Self Leveling Laser System
- 3. Qooltek Multipurpose Laser Level
- 4. DEWALT DW089K Self-Leveling Line laser
- 5. Johnson Level & Tool 40-0921Self Leveling Laser
- 6. PLS Laser PLS-60521 Laser Level Tool
- 7. Bosch GLL 30 Self leveling Cross Line laser
- 8. Bosch GLL 1P Combination Point and Line Laser
- 9. Firecore Self-Leveling Horizontal/Vertical Cross Laser
- 10. STANLEY STHT77340 Cross Line Laser
No DIY project, big or small should be taken on without having the best self leveling laser possible. Nothing is more frustrating than when measurements don’t line up and you are left admiring your very skew project. So although you might be tempted to cut corners and go for the best cheap laser level, you might want to shop around a bit and invest long term in a professional level.
Buyers Guide Questions
What is laser level?
A laser level is a construction tool which measures levelness by projecting a red or green light beam onto a flat surface. Laser levels are used to deduct how level or straight a surface is by projecting a light beam across or around it. Small traditional laser levels can be used for in and around the home DIY projects while the bigger, more industrial types are better suited for outdoor and construction job sites.
Home DIY projects such as hanging picture frames or laying down carpets benefit tremendously from incorporating a laser level. A good quality laser level cuts down on the amount of measuring one would normally do and it takes the guess work out of knowing whether a surface is level or not. The important thing to remember is that these are lasers and should never be directed at another person’s eyes.
Most laser levels are manufactured with a low intensity diode and are battery operated, allowing you freedom of movement without tripping over long extension cords. The level needed will very much depend on the size of the project on hand or whether it is indoors or outdoors. If you only need to hang a few picture frames then it would not make sense to buy an expensive industrial professional laser level. In the same way, a large bulky laser level might cause more hassles than good when used for small DIY jobs around the home.
Laser levels can be self leveling which means that they are able to detect the level area with the help of internal self leveling sensors. These lasers are more time effective as well as accurate than their manually set counterparts. Most level lasers can be divided into three categories; plumb, line level and rotary lasers. Plumb lasers have a dot sight or reference point unlike line lasers which project a visual line or two cross lines. Lastly, rotary lasers project a level line around the entire room and are usually more bulky in appearance.
How laser levels work?
Laser levels use a laser beam to pin point the origin of levelness on a flat surface. The beam of light which is projected from a laser level is emitted through a device called a diode. The word “laser” is actually an acronym and stands for Light Amplification by the Stipulated Emission of Radiation. Quite a mouthful but simply put, it is when stimulated electrons give off a beam of light which is then collected by mirrors or prisms and pointed in a certain direction.
The end result is a laser beam. Level lasers are used to project a line which can be used as a visual chalk line onto a surface. The thickness of the line will depend on the size of the diode. A thinner projection beam will be more accurate than a thicker beam as the reference point would then be within the beam somewhere.
Level lasers can be used indoors and outdoors but there was a time when they were limited to indoor use because the laser beam was too weak to be seen outdoors. Nowadays, we have more powerful lasers with the added benefit of audible level detectors which give off a beeping sound once the level has been reached. Most laser levels come with some kind of swivel attachment bracket or tripod so as to keep the laser level and steady.
A few have self leveling capabilities while others operate manually. Self leveling lasers have the ability to detect the level by using electronic sensors while manual levels make use of the traditonal bubble vial. Self leveling lasers might be more accurate in some ways but their electronic extras will drain your battery power much faster than a manual laser level with a bubble vial.
How to use laser level to hang Pictures?
Probably the most common use for a small home diy level laser would be to hang pictures or frames. Of course you can hang a picture frame or a piece of art without using a laser level but why take the chances of having a skew end product? A laser level will help you hang level and centered picture frames each and every time with little to no hassle at all. Follow these easy guidelines and you will have perfectly straight wall art in no time flat.
Step 1: To begin, measure the width of the wall you will be using and the width of the picture frame you will be hanging.
Step 2: Choose the desired height for the top part of the picture frame and make a small pencil mark within the measured height.
Step 3: Use your tool to project a line horizontally across the pencil mark.
Step 4: Carefully adjust the laser until the bubble in the vial is centered and resting between the black lines and the beam is projecting onto or through the pencil mark.
Step 5: Once you are satisfied that the laser beam is passing correctly through the pencil mark, you can them fasten or mount the laser level device.
Step 6: Next, you should measure the distance from the top part of the frame to its hanging point. This is usually the small hook or string on the back of picture frames.
Step 7: Using that measurement, measure down from where the pencil mark and laser beam meet and make yet another pencil mark at this point. This mark is where your picture frame will hang from when you are done.
Step 8: Carefully hammer a nail into this pencil mark. Alternatively, you can use a nail gun – read the full guide here. Place your picture frame onto the hook and align it with the laser beam before securing it in place.
As you can see in just a few minutes you could have a perfectly straight wall decoration with almost no hassles at all. So why would you even try to hang wall art without a laser level?
How to Check Laser Level for Accuracy?
When taking on any size project, it is always better to measure twice and cut once so they say. Although a laser level is your best and most accurate option for measuring levelness, it won’t hurt to just do a double check. The best way to do this would be to check the accuracy of your laser level before you begin your project. Even the best laser levels may become less calibrated over time and need to be checked on a regular basis. Take a few minutes to follow these few steps and you will be saving yourself the embarrassment of an unlevel project.
Step 1: Place it on a tripod in the centre of a large room. The exact position of the tripod is not important but it should be at least 20 ft from the walls of the room.
Step 2: turn your laser on and project a vertical line against the wall. Mark off the point where the laser hits the wall with a pencil.
Step 3: Rotate the tool by 180 degrees and mark that point with a pencil. Compare the two marks and see if the difference is within the general range or not.
Step 4: Rotate the level by 90 degrees and mark off the point against the wall. Repeat the process again for 180 degrees then check the difference again. If the vertical beam is not within reach or if the axis fails to show the proper results then your laser level may need to be calibrated.
What is the best Laser Level on the Market?
According to reviews, the DEWALT DW089K Self-leveling 3-Beam Line Laser takes the prize as the best laser on the market. The DEWALT DW089K features three beams to aid in 90 degree layouts as well as a 165 ft range with fulltime pulse mode. It is accurate within 1/8 of an inch which is pretty damn close to being spot on. This product is ideal for installing cabinets and drop ceilings or windows and doors. Reviews showed that this product was able to take a beating without breaking down.
Not only is the DEWALT DW089K sturdy and reliable it is also steady and bright when placed onto a tripod. Unlike any other line lasers on the market, the DEWALT DW089K features a second plumb line which forms a 90 degree intersecting line on the floor and ceiling. This third line can be used for layout applications without actually needing a second line laser device.
A micro-adjust knob allows the level to line up accurately and the whole unit is powered by simple AAA batteries. Even with its extra features, the device has a long-lasting 30 hour extended battery life. The DEWALT DW089K Self-leveling 3-Beam Line Laser is the most certainly top notch and it would be a solid investment for any avid DIY warrior or construction job site. Take a look at our other best of reviews at our homepage here.
What’s the best Rotary Laser Level on the Market?
The Johnson-Level-Tool-99-006K-Self-Leveling Rotary System knocks all other rotary laser kits out of the park when it comes to features. With an Automatic leveling in the horizontal plane and a 90 degree manual leveling vertical plane it is sure to make any construction job easier. When not in use, the automatic locking system protects the pendulum from any hard knocks or bumps.
Choose between 200, 400 or 600RPM, depending on the size of the project at hand. Comes standard with a tripod stand and laser detector as well as tinted laser enhancement safety glasses for eye protection and better visibility while in use. Positive reviews from customers state that the laser is accurate from a distance as far as 70 ft. They also stated that set up was moderately easy thanks to the clear instruction manual.
Top reviews stated that even in bright sunlit conditions, the laser was still highly visible and accurate. Moderately priced, this rotary laser level is the obvious choice for anyone looking for a professional construction tool which is affordable.
What is the Difference Between Red and Green Laser Beams?
The green or red light beam which a laser level projects are not just there for color. As a matter of fact, the color of the beam can tell you quite a bit about the laser level in question. Green laser beams are up to four times brighter than standard red laser beams thus making them more visible to the user.
These are best for use in very bright conditions such as outside on a sunny day or when working under bright lights. Both red and green lasers will stand up to any challenge, however there are some instances where the green lasers can perform better. It has a much higher visibility rate which makes it the best option for long distance measuring.
Unfortunately, greener laser beams and their diodes are more difficult to manufacture than standard red laser beams. This causes a fluctuation in the cost of green laser level tools making them more expensive than red ones. A complete assessment of the nature of the project will help you decide whether a red or green laser beam is the best option.
The DEWALT DW088K Cross Line Laser is hands down our top choice. It features Two bright crossing beams which are highly accurate for 1/8 “ up to 30 ft. It comes with a built in magnetic base for easy mounting on metal surfaces. The over-molded housing cover is water and debris resistance and the laser has a three year limited warranty which comes with a one year free service.
This class 2 laser has a 100ft visibility range for indoors and a self leveling range of +/- 4 degrees. Uses three AAA batteries which are included. The side control panel features individual buttons which control all three beams and the laser is stored in a hard sided kit box for easy transport. This is the best laser for anyone looking to purchase a tool which is easy enough to use at home yet is sturdy and reliable enough for construction size jobs too.
The Johnson-Level-Tool-99-006K is our premium pick for the best self-leveling. It features visual and audible alarms when out of leveling range and rotates at 200, 400 and 600 RPM. The rate of the rotation will be decided by the size of the project you are planning. The laser beam has a full 360 degree rotation and can be used vertically or horizontally with a 90 degree split beam feature.
The housing composite is high impact tough and durable which makes it tough enough for job sites. This laser comes standard with a aluminium tripod and 13ft aluminium grade rod. The kit also contains a detector for outside jobs and a wall/ceiling mount with clamp. Battery operated and easy to use, this is a premium choice for little jobs around the home or accomplished tradesman alike. If you are on the hunt for a laser level which packs a lot of features but is uncomplicated then this is definitely for you.
The Qooltek is value packed with features for its size which makes it the best and great value for money. Its 3 prong approach consists of a 8 ft tape measure, triple positioned leveling bubble vial and a new laser level to provide optimum results every time. This little laser level is ready for action anytime accurate measurements need to be taken.
It comes with a back up battery to keep you going for those longer projects. Easy operation thanks to the simple on/off laser light switch and has a Max Power Output of 3.5mW. Lightweight and easy to use, this would be the perfect gift for a DIY Dad. Its so easy to use that even Mom can use it for her craft projects or hanging a picture frame with out any help at all.